Skip to content
  • About
  • Contact
  • Login / Register
Makers HutMakers Hut
  • Basket / £0.00 0
    • No products in the basket.

  • Checkout +
  • 0

    Basket

    No products in the basket.

Home / 3D Printer / Parts & Accessories

3D Printer Filament Break Detection Module RepRap CR-10S Prusa

£9.99

Clear
3D Printer Filament Break Detection Module RepRap CR-10S Prusa
SKU: 3DP-PAR-194 Category: Parts & Accessories Tags: 3D Printer, CR-10, Detection Module, Filament Break, prusa, reprap
Product Categories
  • 3D Printer
    • Controllers
    • Filament
    • Kits
    • Parts & Accessories
  • Arduino
    • Boards
    • Kits
    • Shields and Accessories
  • Cooling
    • Fan Guards
    • Fans
    • Heatsinks
  • Drone
  • Drones and More
    • Accessories
    • Antennas
    • Components
    • Drones
    • Kits
  • Electronics
    • Access Control
    • Cable
    • Components and Sensors
    • DIY Kits
  • LED Lighting
    • Accessories
    • Beads
    • Bulbs
    • Controllers
    • DMX
    • Downlights
    • Panel
    • Strips
  • Mechanical
    • Bearing
    • Bearings
      • Ball
      • Bushings
      • Flange
      • Grooved
      • Linear
      • Miniature
      • Needle
      • Self Aligning
      • Self Lube
      • Taper Roller
    • Fluid Transfer
    • Magnets
    • Mounts and Supports
    • Pulleys and Coupler
    • Rails and Carriage
    • Rods
    • Rods and Carriages
    • Timing Belt
  • Microcontrollers
  • Miscellaneous
  • Motors
    • Accessories
    • Coreless
    • DC Motors
    • Drivers
    • Spindle
    • Step
  • Other
  • Power Supply
  • Raspberry Pi
    • Boards and Kits
    • Shields and Accessories
  • Robotics
    • Components
    • Kits
  • Uncategorised
  • Virtual Reality
  • Description
  • Additional information

Description:

3D Printer Filament Break Detection Module with 1m wire

How it works:

The material detection module uses the level hopping detection mode: When there is material, the signal of the detection port level should be high. When there is no material, the material level signal goes low, and the system detects a certain high Level to low level of the jump, then that the material run out, the implementation of the suspension order, waiting for the operator to replace the material to continue the print.

CR10S has a dedicated filament sensor port. If you are using this for CR-10, you will need a breakout board to access pin 27.

What you will receive:

1 x Break Detection Module

 

 

 

Weight N/A
Filament

1.75mm, 3mm

Related products

Quick View

Parts & Accessories

40W Ceramic Cartridge Heater- Right Angle 12V Heating Element – 3D Printer – Reprap

£3.99
Quick View

Parts & Accessories

Carriage for Kossel or Rostock – RepRap Delta 3D Printer

£44.99
Quick View

Kits

2020 Aluminum Extrusion for Kossel & Kossel XL – RepRap Delta 3D Printer

£64.99 – £69.49
Quick View
Out of stock

Parts & Accessories

Bowden Aluminum Extruder Upgrade – 3D Printer Reprap Kossel Prusa – Right

£21.99
Quick View

Parts & Accessories

40W Ceramic Cartridge Heater- Straight 12V Heating Element – 3D Printer – RepRap

£2.99
40W Ceramic Cartridge Heater- Straight 12V Heating Element - 3D Printer
Quick View

Parts & Accessories

60W Ceramic Cartridge Heater – 24V Heating Element – 3D Printer – RepRap

£4.99
Quick View
Out of stock

Parts & Accessories

Carriage for Kossel or Rostock – RepRap Delta 3D Printer

£42.99
Quick View

Parts & Accessories

Delta Robot Aluminum End Effector Mount – Kossel RepRap 3D Printer

£14.99 – £18.99
  • About
  • Contact
Copyright 2021 © Makers Hut
  • 3D Printer
  • Arduino
  • Cooling
  • Drones and More
  • Electronics
  • LED Lighting
  • Mechanical
  • Microcontrollers
  • Miscellaneous
  • Motors
  • Power Supply
  • Raspberry Pi
  • Robotics
  • Virtual Reality
  • Contact
  • Buy now