Skip to content
  • About
  • Contact
  • Login / Register
Makers HutMakers Hut
  • Basket / £0.00 0
    • No products in the basket.

  • Checkout +
  • 0

    Basket

    No products in the basket.

Home / Electronics / Components and Sensors

Monochrome 0.96″ 128×64 OLED Graphic Display – STEMMA QT

£19.29

2 in stock

Monochrome 0.96″ 128×64 OLED Graphic Display – STEMMA QT

£19.29

SKU: ELE-COM-063 Category: Components and Sensors Tags: adafruit, arduino, Monochrome, OLED Graphic Display
Product Categories
  • 3D Printer
    • Controllers
    • Filament
    • Kits
    • Parts & Accessories
  • Arduino
    • Boards
    • Kits
    • Shields and Accessories
  • Cooling
    • Fan Guards
    • Fans
    • Heatsinks
  • Drone
  • Drones and More
    • Accessories
    • Antennas
    • Components
    • Drones
    • Kits
  • Electronics
    • Access Control
    • Cable
    • Components and Sensors
    • DIY Kits
  • LED Lighting
    • Accessories
    • Beads
    • Bulbs
    • Controllers
    • DMX
    • Downlights
    • Panel
    • Strips
  • Mechanical
    • Bearing
    • Bearings
      • Ball
      • Bushings
      • Flange
      • Grooved
      • Linear
      • Miniature
      • Needle
      • Self Aligning
      • Self Lube
      • Taper Roller
    • Fluid Transfer
    • Magnets
    • Mounts and Supports
    • Pulleys and Coupler
    • Rails and Carriage
    • Rods
    • Rods and Carriages
    • Timing Belt
  • Microcontrollers
  • Miscellaneous
  • Motors
    • Accessories
    • Coreless
    • DC Motors
    • Drivers
    • Spindle
    • Step
  • Other
  • Power Supply
  • Raspberry Pi
    • Boards and Kits
    • Shields and Accessories
  • Robotics
    • Components
    • Kits
  • Uncategorised
  • Virtual Reality
  • Description
  • Additional information

Description:
These displays are small, only about 1″ diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128×64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its crispness!

This breakout can be used with either an SPI or I2C interface – selectable by cutting two jumpers on the back. The design is completely 5V-ready, with an onboard regulator and built-in boost converter. It’s easier than ever to connect directly to your 3V or 5V microcontroller without needing any kind of level shifter!

We’ve updated the design to add auto-reset circuitry so that the reset pin is optional, since it speaks I2C you can easily connect it up with just two wires (plus power and ground!). We’ve even included SparkFun qwiic compatible STEMMA QT connectors for the I2C bus so you don’t even need to solder when you purchase and attach a STEMMA QT cable! QT Cable is not included.

Please note that OLED displays are made of hundreds of…OLEDs! That means each pixel is a little organic LED, and if it’s kept on for over 1000 hours it’ll start to dim. If you want to keep the display uniformly bright, please turn off the display (set the pixels off) when it isn’t needed to keep them from dimming.

Technical Details:
EagleCAD PCB files, Fritzing, and datasheets available in the product tutorial

Revision History:

As of August 3, 2020 we have revised this PCB to be a little smaller, added auto-reset circuitry so the RESET pin is not required, made I2C the default configuration, and added 2 STEMMA QT connectors for easy plug-and-play usage.

Dimensions:

PCB: 29.2mm x 26.7mm (1.1″ x 1″)
Screen: 26.6mm x 19mm
Thickness: 6.2mm
Weight: 4.5g
Distance between mounting holes: 24mm
Display current draw is completely dependent on your usage: each OLED LED draws current when on so the more pixels you have lit, the more current is used. They tend to draw ~20mA or so in practice but for precise numbers you must measure the current in your usage circuit.
This board/chip uses I2C 7-bit address between 0x3C-0x3D, selectable with jumpers

What you will receive:

1 x Monochrome 0.96″ 128×64 OLED Graphic Display

Weight 9 g

Related products

Arduino Proto Screw Shield Board Rev 3.1 - Prototyping DIY Uno
Quick View
Out of stock

Shields and Accessories

Arduino Proto Screw Shield Board Rev 3.1 – Prototyping DIY Uno

£3.99
Raindrop Detection Sensor Module Humidity Rain Drop For Arduino PI
Quick View

Shields and Accessories

Raindrop Detection Sensor Module Humidity Rain Drop For Arduino PI

£2.29
Quick View

Shields and Accessories

High Sensitivity Microphone Sensor Sound Detection For Arduino Module KY-037

£2.99
Quick View

Microcontrollers

LilyPad 328 Main Board ATmega328P 16M for Arduino 16 MHz UK Stock

£5.99
Quick View

Shields and Accessories

Motor Drive Expansion Shield Board Module L293D For Arduino Duemilanove Mega UNO

£3.89
Quick View

Shields and Accessories

Ultrasonic Sensor Mounting Bracket Mount HC-SR04 Smart Car Arduino

£1.99
Quick View
Out of stock

Shields and Accessories

Prototype Shield I/O Expansion Module Extension Board For Arduino Nano

£3.49
Quick View

Microcontrollers

Arduino UNO R3 Wifi Board ESP8266 ESP-12F MEGA328P ATMEGA16U2

£9.85
  • About
  • Contact
Copyright 2021 © Makers Hut
  • 3D Printer
  • Arduino
  • Cooling
  • Drones and More
  • Electronics
  • LED Lighting
  • Mechanical
  • Microcontrollers
  • Miscellaneous
  • Motors
  • Power Supply
  • Raspberry Pi
  • Robotics
  • Virtual Reality
  • Contact
  • Buy now